Klüber oil & grease lubricants
-
Starting at: € 340,80 / Kg -
Klüber ISOFLEX PDL 300 A
Quick orderingMore infoKlüber ISOFLEX PDL 300 A
High-performance grease for rolling bearings operating at low temperatures
Application Klüber ISOFLEX PDL 300 A
ISOFLEX PDL 300 A is suitable for plain and rolling bearings, and for sliding points such as cams, bolts, meters, cam plates, and adjusting rings used in automotive, telecommunications and precision engineering, in instruments, and in cryotechnology applications.
Show moreStarting at: € 325,96 / Kg -
Klüber Summit SH 46 XS
Quick orderingMore infoKlüber Summit SH 46 XS
Synthetic air compressor oil enabling oil change intervals up to 10,000 operating hours
Application Klüber Summit SH 46 XS
Klüber Summit SH 46 SX was especially developed for the lubrication of highly loaded rotary screw compressors which require an oil formulated without the use of silicone raw materials. Klüber Summit SH 46 XS is intended for oil-injected rotary screw compressors with oil change intervals of up to 10,000 operating hours. Used compressors can be switched over from conventional mineral oils to Klüber Summit SH 46 XS. Klüber Summit SH 46 XS is neutral towards most elastomers typically used in air compressors - no leakage is to be expected. Klüber Summit SH 46 XS offers very good oxidation stability due to the synthetic base oil, thus minimising oxidation residues in the compressor and extending oil change intervals and the service life of the oil separator. The product contains special inhibitors to largely prevent the formation of residues in the compressors. Owing to the evaporation stability of the base oil, the oil vapour content in the compressed air can be considerably reduced compared to conventional mineral oils. This contributes to a reduction of oil consumption and clean compressed air; gumming of pneumatic valves in the compressed air circuit can be prevented as well due to the low oil content in the compressed air.
Show more€ 38,09 / L -
Klüber Summit SH 55
Quick orderingMore infoKlüber Klüber Summit SH 55
Synthetic air compressor oils for oil change intervals up to 10,000 operating hours
Application Klüber Klüber Summit SH 55
Klüber Summit SH oils have been designed especially for the lubrication of highly loaded, oil-injected screw-type compressors with oil change intervals up to 10,000 operating hours. Klüber Summit SH oils can also be used for compressors that were previously run with mineral oils. They are neutral towards most elastomer seals used in air compressors, therefore leakage is not to be expected. Klüber Summit SH 32 is especially suitable for centrifugal compressors and Klüber Summit SH 100 for reciprocating piston compressors. Klüber Summit SH oils offer good oxidation stability due to the synthetic base oil, thus minimizing oxidation residues in the compressors and extending oil change intervals and the service life of oil filters and separators. Special inhibitors contained in the oils keep the inside of compressors clean. Owing to the evaporation stability of the base oil, the oil vapour content in the compressed air can be considerably reduced compared to conventional mineral oils. This contributes to a reduction of oil consumption and clean compressed air; gumming of pneumatic valves in the compressed air circuit can be prevented as well due to the low oil content of the Klüber Summit SH oils.
Show moreStarting at: € 30,80 / L -
Klüberoil GEM 1-680 N
Quick orderingMore infoKlüberoil GEM 1-680 N
High-performance gear and multipurpose oil based on mineral oil with KlüberComp Lube Technology
Application Klüberoil GEM 1-680 N
Klüberoil GEM 1 N was specially developed for the lubrication of spur, bevel, hypoid and planetary gears that are subject to high loads. Such gears are frequently used in the steel, mining and sugar industries. It is also used for the lubrication of standard worm gears as defined in DIN 3996. Klüberoil GEM 1 N can also be used for the lubrication of plain and rolling bearings, all kinds of toothed couplings, chains, guideways, joints, spindles and pumps.
Show moreStarting at: € 19,02 / L - Starting at: € 62,11 / L
-
Klüber Summit SH 32
Quick orderingMore infoKlüber Summit SH 32
Synthetic air compressor oils for oil change intervals up to 10,000 operating hours
Application Klüber Summit SH 32
Klüber Summit SH oils have been designed especially for the lubrication of highly loaded, oil-injected screw-type compressors with oil change intervals up to 10,000 operating hours. Klüber Summit SH oils can also be used for compressors that were previously run with mineral oils. They are neutral towards most elastomer seals used in air compressors, therefore leakage is not to be expected. Klüber Summit SH 32 is especially suitable for centrifugal compressors and Klüber Summit SH 100 for reciprocating piston compressors. Klüber Summit SH oils offer good oxidation stability due to the synthetic base oil, thus minimizing oxidation residues in the compressors and extending oil change intervals and the service life of oil filters and separators. Special inhibitors contained in the oils keep the inside of compressors clean. Owing to the evaporation stability of the base oil, the oil vapour content in the compressed air can be considerably reduced compared to conventional mineral oils. This contributes to a reduction of oil consumption and clean compressed air; gumming of pneumatic valves in the compressed air circuit can be prevented as well due to the low oil content of the Klüber Summit SH oils.
Show moreStarting at: € 27,05 / L -
Klübersynth GEM 4-220 N
Quick orderingMore infoKlübersynth G 4-220
Synthetic high-performance gear oil
Application Klübersynth G 4-220
Klübersynth G 4 was especially developed for the lubrication of spur, bevel and planetary gears. It can also be used for plain and rolling bearings.
Show moreStarting at: € 32,27 / L -
Klüber Summit DSL 68
Quick orderingMore infoKlüber Summit DSL 68
Full synthetic air compressors for oil compression intervals up to 8,000 operating hours
Applying Klüber Summit DSL 68
The Klüber Summit DSL 68 oil is specially designed for oil freshening intervals of up to 8,000 operating hours* in oil-injected propeller compressors. Klüber Summit DSL 32 and 46 can also be used for lubricating centrifugal compressors, while Klüber Summit DSL 68 is particularly suitable for the lubrication piston compressors. Klüber Summit DSL oils are used for compressors previously used with conventional mineral oils. These oils are neutral compared to most elastomer seals used in air compressors, so leakage is not to be expected. Klüber Summit DSL 68 is biodegradable and can therefore be used in environmentally friendly applications. Klüber Summit DSL 68 oil offer good oxidation stability thanks to the synthetic base oil, minimising oxidative residues in the compressors in the oil freshening intervals and extending the life of oil filters and separators (screw compressors) and valves (piston compressors).
Show moreStarting at: € 29,81 / L -
Klüber Tyreno Fluid 6/14V
Quick orderingMore infoKlüber Tyreno Fluid 6/14V
High-performance vacuum pump oils for fine- and high-vacuum applications
Application Klüber Tyreno Fluid 6/14V
Klüber Tyreno Fluids are tried-and-tested as filling fluids in mechanical backing pumps, diffusion pumps and turbomolecular pumps by leading OEMs. They are also suitable for pumping gasous oxygen. Klüber Tyreno Fluids have been tested as filling fluids according to the Autogeneous Ignition Temperature (AIT) procedure. Klüber Tyreno Fluids can also be used as vapour-resistant, chemically inert transmission fluid in dry-running screw-type pumps. Klüber Tyreno Fluids can also be used as sliding agent for the lubrication of valves, fittings and installations carrying gaseous oxygen or for chemical plants and apparatus requiring good resistance to various gases (conclusion by analogy based on chemical composition. For this purpose, we recommend users conduct their tests using the complete component under conditions similar to series application. Test results show the products' usability for an O2 content > 21 % by vol. under operating conditions specified in the product data section of this product information leaflet. Behaviour towards metal, elastomers and plastics Klüber Tyreno Fluid 3/6V, 6/14V, 12/25V are normally neutral towards metallic materials, plastics and elastomers within the envisaged temperature range. Nevertheless, we recommend checking the compatibility of the product with materials prior to the introduction of this product.
Show moreStarting at: € 757,29 - € 758,04 / L
-
Klüber Klübersynth GEM 4-46 N
Quick orderingMore infoKlüber Klübersynth GEM 4-46 N
Synthetic high-performance gear and multipurpose oil with KlüberComp Lube Technology
Application Klüber Klübersynth GEM 4-46 N
Klübersynth GEM 4 N was specially developed for the lubrication of spur, bevel, hypoid and planetary gears that are subject to high loads. Such gears are frequently used in the wind, steel, mining and sugar industries. It is also used for the lubrication of standard worm gears as defined in DIN 3996. Klübersynth GEM 4 N can also be used for the lubrication of plain and rolling bearings, all kinds of toothed couplings, chains, guideways, joints, spindles and pumps, especially in applications where the equipment is exposed to elevated temperatures or pronounced temperature fluctuations.
Show moreStarting at: € 36,06 / L -
Klüber HOTEMP PLUS
Quick orderingMore infoKlüber HOTEMP PLUS
High-temperature chain oil
Application Klüber HOTEMP PLUS
HOTEMP PLUS is suitable for all oil-lubricated stenter chains such as – roller chains, – chains or clips with ball bearings in cases of combined lubrication of bearings, chain joints and slide ways, and – slide chains with lubrication of slide rails, chain joints and bolts in equalizing frames, single-layer stenters, tier stenters, festoon driers and steamers as well as installations.
Show moreStarting at: € 76,05 / L -
Klüber Lamora D 100
Quick orderingMore infoKlüber Lamora D 100
Lubricating oils for slideways and guideways
Application Klüber Lamora D 100
LAMORA D oils are especially suited for the lubrication of heavily loaded slideways with low feed rates. LAMORA D oils have been tried and tested for the lubrication of slideways and guideways in modern machining centres, milling machines, lathes and other machine tools. As they show good compatibility with water-miscible machining fluids and cooling lubricants, LAMORA D oils can be used in applications where they may mix with aqueous media.
Show moreStarting at: € 24,71 / L -
Klüber Lamora D 150
Quick orderingMore infoKlüber Lamora D 150
Lubricating oils for slideways and guideways
Application Klüber Lamora D 150
LAMORA D oils are especially suited for the lubrication of heavily loaded slideways with low feed rates. LAMORA D oils have been tried and tested for the lubrication of slideways and guideways in modern machining centres, milling machines, lathes and other machine tools. As they show good compatibility with water-miscible machining fluids and cooling lubricants, LAMORA D oils can be used in applications where they may mix with aqueous media.
Show moreStarting at: € 22,50 / L -
Klüber Klüberbio EG 2-100
Quick orderingMore infoKlüber Klüberbio EG 2-100
Environmentally compatible, synthetic high-performance gear oils
Application Klüber Klüberbio EG 2-100
Klüberbio EG 2 oils were developed for the lubrication of ships’ gearboxes, particularly for thrusters and rudder propellers. Leading manufacturers of thrusters and propeller shaft seals have tested and approved these oils. Please contact Klüber Lubrication or the manufacturer of the seal or thruster for technical consultation on your specific seallubricant combination. Klüberbio EG 2 oils protect rolling elements effectively against wear and pitting, thus complying with the requirements of rolling bearing manufacturers for highly loaded, large rolling bearings in pod drives. Klüberbio EG 2-68, 100 and 320 oils can also be used for the lubrication of open-running drive and conveyor chains, e.g. in installations and machines in agriculture, forestry and water resources industries as well as for horticultural appliances.
Show moreStarting at: € 30,00 / L -
Klüber Klübersynth GE 4 75W90
Quick orderingMore infoKlüber Klübersynth GE 4 75 W 90
Synthetic high-performance gear oil
Application Klüber Klübersynth GE 4 75 W 90
Klübersynth GE 4 75 W 90 is used for the lubrication of spur, bevel and hypoid gears requiring maximum wear protection and service life, even when exposed to impact loads. Klübersynth GE 4 75 W 90 is suitable for drives in rail vehicles, industrial robots, textile machines and forming presses.
Show moreStarting at: € 30,08 / L -
Klüber Klübersynth EG 4-680
Quick orderingMore infoKlüber KlübersynthEG 4-680
Synthetic high-performance gear oil
Application Klüber Klübersynth EG 4-680
Klübersynth EG 4 was especially developed for the lubrication of heavily loaded spur, bevel and planetary gears. It can also be used for the lubrication of worm gears. Klüberoil EG 4 can also be selected for the lubrication of plain and rolling bearings, all kinds of toothed couplings, chains, guideways, joints, spindles and pumps.
Show moreStarting at: € 32,67 / L -
Klüber Klübersynth CTH 2-260
Quick orderingMore infoKlüber Klübersynth CTH 2-260
High-temperature oil for oil-lubricated stenter chains in the textile industry
Application Klüber Klübersynth CTH 2-260
With Klübersynth CTH 2-260, the range of Klüber Lubrication high-temperature chain oils has been consistently upgraded. The product can replace other Klüber Lubrication chain oils for high operating temperatures. It can be used for all types of oil-lubricated stenter chains, e.g. roller chains; chains or clips with ball bearings - combined lubrication of ball bearings, chain links and sliding rails; sliding chains in single-layer stenters, multi-layer stenters, festoon dryers, festoon steamers, coating installations - lubrication of sliding rails, chain links and chain pins
Show moreStarting at: € 78,86 / L -
Klüber Klüberalfa YM 3-30 N
Quick orderingMore infoKlüber Klüberalfa YM 3-30 N
Lubricating oils for synthetic material friction points with good wetting properties
Application Klüber Klüberalfa YM 3-30 N
Klüberalfa YM 3-30 N and Klüberalfa YM 3-65 N can be used for the wetting of metals and synthetic material parts of various configurations. Due to their good material compatibility, these products should be your first choice for the vehicle interior. Application examples: – Guide bars of headrests – Impact, rubbing and sliding points, even of various material pairings, to minimise annoying noises in the components such as fittings, sliding guides in the centre console, cup holder, navigation screen, locking mechanism of trays, ventilation outlet valve, etc. General conduct toward synthetic materials and elastomers: Perfluoropolyethers are generally to be classified as widely neutral (possible exception: high fluorinated FKMs) in comparison to elastomers and synthetic materials. Despite this, prior to a series application, the compatibility of the lubricant with the material with which it is to come into contact, must be confirmed.
Show moreStarting at: € 790,36
Küber lubricants
High-performance Klüber oils and greases for optimal lubrication of assets. Resulting in higher reliability, less time spent on maintenance and lower lubricant consumption. With a lower cost to operate, fewer breakdowns, more performance, more output and a better result. Also food safe or biodegradable if required, with the official registrations and certifications.
What makes Klüber lubricants so good?
Klüber is the specialist for special greases and oils. I think there is no other brand with such a broad portfolio of lubricating greases as Klüber. Kluber's portfolio already includes more than 10,000 products. Therefore, you often see very high-quality and very specific products in their portfolio. The price of this specialist in lubricants is high, but fortunately very small packages are available.
My machine supplier prescribes Klüber lubricants. Should I use these?
Klüber has an extremely good relationship with these OEMs and has often looked very closely at the needs and requirements of these machine builders. Therefore, it is not always obvious to select a general product. In addition, warranty also plays an important role. If the consumption is not very high, we would save you the trouble of looking for an alternative.
Where can I buy Klüber oil in United Kingdom?
The easiest way is online! OilOnline delivers Klüber oil and greases in the whole Benelux. They are specialised in business use, but the private individual can also buy directly from the wholesaler.
Our customers value us
Ian Adair
"We like your site, it shows that you are experts in lubricants!"
Cris Scullion
"You deliver quicker than our previous UK supplier!"
Stuart Wyatt
"Surprise to us!
We paid to much in the past"
Our customers value us
Ian Adair
"We like your site, it shows that you are experts in lubricants!"
Cris Scullion
"You deliver quicker than our previous UK supplier!"
Stuart Wyatt
"Surprise to us!
We paid to much in the past"
Discover the benefits of OilOnline!
Are you looking to buy oil from OilOnline? Then you can take advantage of many benefits:
Our knowledge
is your strength!
At OilOnline, we have a team of passionate lubricant specialists with extensive knowledge and experience.
Detailed
advice
Our experts will assist you in choosing the best products, so you can get the most out of your vehicle or machine.
Uncompromising
Quality
At OilOnline, we only offer lubricants from globally renowned quality brands.
Save on
Lubricants
By ordering larger quantities, you can take advantage of price benefits at OilOnline.