Klüber oil & grease lubricants

Klüber Klüberalfa MR 3-800

Universal sliding fluid for seals, guideways and plastic friction points

Application Klüber Klüberalfa MR 3-800

Due to its good compatibility, Klüberalfa MR 3 may be used in combination with most materials, e.g. leather, textile or plastic, in car interiors or on the car body. Klüberalfa MR 3 is compatible with most thermoplastics or thermosetting plastics used, for example, in dashboards, seat and sunroof sliding rails, arm rests, seat adjustment mechanisms, door and sunroof seals. Perfluorinated polyether oils are generally regarded as neutral towards elastomers and plastics (possible exception: highly fluorinated rubber). Nevertheless we recommend testing compatibility with the material to be used, especially prior to series application.

Klüber Summit SH 100

Synthetic air compressor oils for oil change intervals up to 10,000 operating hours

Application Klüber Summit SH 100

Klüber Summit SH oils have been designed especially for the lubrication of highly loaded, oil-injected screw-type compressors with oil change intervals up to 10,000 operating hours. Klüber Summit SH oils can also be used for compressors that were previously run with mineral oils. They are neutral towards most elastomer seals used in air compressors, therefore leakage is not to be expected. Klüber Summit SH 32 is especially suitable for centrifugal compressors and Klüber Summit SH 100 for reciprocating piston compressors. Klüber Summit SH oils offer good oxidation stability due to the synthetic base oil, thus minimizing oxidation residues in the compressors and extending oil change intervals and the service life of oil filters and separators. Special inhibitors contained in the oils keep the inside of compressors clean. Owing to the evaporation stability of the base oil, the oil vapour content in the compressed air can be considerably reduced compared to conventional mineral oils. This contributes to a reduction of oil consumption and clean compressed air; gumming of pneumatic valves in the compressed air circuit can be prevented as well due to the low oil content of the Klüber Summit SH oils.

Klüber Klüberfluid D-F 1 Ultra

Repair lubricant for open girth gear drives

Application Klüber Klüberfluid D-F 1 Ultra

Klüberfluid D-F 1 ULTRA was specially developed for repair lubrication of damaged open gears. It is also highly suitable for rapid running-in of new or newly aligned gear sets such as those used with rotary kilns, tube kilns and winches, for example in the cement industry, power generation, mining, chemical industry, paper and sugar industry as well as the marine sector.

Klüber Klüberalfa KR 3-730

Protecting and lubricating fluid for plug-in contacts

Application Klüber Klüberalfa KR 3-730

Klüberalfa KR 3-730 is suitable for the large-batch oiling of plug-in contacts of different shapes and materials which have to the meet high requirements in e.g. telecommunications, automation technology or car manufacture. In-house tests have shown that the protecting effect of Klüberalfa KR 3-370 is best on lead-free tin alloys. Optimum results are achieved with contact forces below 5 N.

Klüber Summit Supra 32

Fully synthetic air compressor oils based on polyglycol

Application Klüber Summit Supra 32

Klüber Summit Supra Coolant and Klüber Summit Supra 32 have been especially designed for oil change intervals up to 8,000 operating hours in oil-injected screw-type compressors which are prefilled by the manufacturer with polyglycol oil. Due to the specific viscosity and special formulation, Klüber Summit Supra 32 is also suitable for the lubrication of turbocompressors. Klüber Summit Supra 26 N was especially developed for turbocompressors in order to meet the OEMs' viscosity requirements. An oil change interval of up to 40,000 operating hours is possible for turbocompressors, depending on the operating conditions. To enable Klüber Summit Supra 26 N achieve this oil service life it is indispensable to perform an oil condition monitoring every six months. Without prior oil analysis no conclusion can be drawn on the oil's suitability for further use. Klüber Summit Supra oils can be mixed with other polyglycol oils and the Klüber Summit Ultima series. The products are not miscible with mineral oils and synthetic hydrocarbon oils.

Klüber Klübersynth 50 KV

Synthetic high-performance gear oils for weaving machines

Application Klüber Klübersynth 50 KV

Klübersynth 50 KV, 80 KV and 100 KV are exclusively recommended by the Italian textile machine OEM ITEMA for the lubrication of gears, bearings and other sliding friction points in Leonardo-type weaving machines. For Leonardo-type weaving machines with oil coolers, ITEMA recommends Klübersynth 50 KV, and for the R 9500-type machines Klübersynth 80 KV.

Klüber Klüberfluid C-F 3 S Ultra

Operational lubricant for large girth gear drives

Application Klüber Klüberfluid C-F 3 S Ultra

Klüberfluid C-F 3 S ULTRA is primarily used for spray lubrication of large gear rim/pinion drives. It can be used with all gear sizes and power ratings. A peripheral speed of 10 m/s should however not be exceeded. Such drives are primilary found in rotary kilns, tube mills, drums and similar machinery used in the cement, lime, gypsum, mining and chemical industries as well as in coal-fired power stations. Further applications are found in sugar and paper production as well as in the marine and offshore sector.

Klüber Klüberfluid C-F 3 Ultra

Operational lubricant for large girth gear drives

Application Klüber Klüberfluid C-F 3 Ultra

Klüberfluid C-F 3 ULTRA can be used for immersion, paddle wheel, circulation and spray lubrication of large girth gear drives. Application possibilities are not restricted, neither by gear sizes nor power ratings. A peripheral speed of 10.0 m/s should not be exceeded. Such drives are found in rotary kilns, tube mills, drums and similar machinery used in the cement, lime, gypsum, mining and chemical industries and in power plants. Further applications are found in sugar and paper production as well as in marine and offshore technology

Klüber Summit Supra Coolant

Fully synthetic air compressor oils based on polyglycol

Application Klüber Summit Supra Coolant

Klüber Summit Supra Coolant and Klüber Summit Supra 32 have been especially designed for oil change intervals up to 8,000 operating hours in oil-injected screw-type compressors which are prefilled by the manufacturer with polyglycol oil. Due to the specific viscosity and special formulation, Klüber Summit Supra 32 is also suitable for the lubrication of turbocompressors. Klüber Summit Supra 26 N was especially developed for turbocompressors in order to meet the OEMs' viscosity requirements. An oil change interval of up to 40,000 operating hours is possible for turbocompressors, depending on the operating conditions. To enable Klüber Summit Supra 26 N achieve this oil service life it is indispensable to perform an oil condition monitoring every six months. Without prior oil analysis no conclusion can be drawn on the oil's suitability for further use. Klüber Summit Supra oils can be mixed with other polyglycol oils and the Klüber Summit Ultima series. The products are not miscible with mineral oils and synthetic hydrocarbon oils.

Klüber Klübersynth 100 KV

Synthetic high-performance gear oils for weaving machines

Application Klüber Klübersynth 100 KV

Klübersynth 50 KV, 80 KV and 100 KV are exclusively recommended by the Italian textile machine OEM ITEMA for the lubrication of gears, bearings and other sliding friction points in Leonardo-type weaving machines. For Leonardo-type weaving machines with oil coolers, ITEMA recommends Klübersynth 50 KV, and for the R 9500-type machines Klübersynth 80 KV.

Klüber Klübersynth UH1 4-18

Synthetic heat carrier and lubricating oil for the food processing and pharmaceutical industries

Application Klüber Klübersynth UH1 4-18

Klübersynth UH1 4-18 should only be used as heat carrier oil for closed systems in the food processing, pharmaceutical and cosmetics industries. Cast housings and rotating unions are known to have minute leaks when exposed to high temperatures. Thus, these applications require an NSF HT1 lubricant for technically unavoidable contact with the food.

Klüber Unimoly Oil 100

Multipurpose oils with solid lubricant

Application Klüber Unimoly Oil 100

UNIMOLY Oils are used for the lubrication of mechanical spur and bevel gears, rolling and plain bearings, chains and spindles.

Klüber Unimoly Oil 220

Multipurpose oils with solid lubricant

Application Klüber Unimoly Oil 220

UNIMOLY Oils are used for the lubrication of mechanical spur and bevel gears, rolling and plain bearings, chains and spindles.

Klüber Klüberfood NH1 CHT 6-220

Synthetic special lubricating oil for chain applications in the food- and pharmaceutical industry

Application Klüber Klüberfood NH1 CHT 6-220

Klüberfood NH1 CHT 6-220 may be applied via suitable chain lubrication system. Compatibility of the lubricant with the materials of the reservoir should be checked. To attain the highest performance in baking ovens, please do not hesitate to consult your local Klüber representative. Mixing of Klüberfood NH1 CHT 6-220 oil with other incompatible or non-food-grade lubricants should be avoided. For object / chain temperatures up to approx. 160 °C resulting e.g. from oven temperatures up to 300 °C under certain operating conditions. We recommend sufficient air removal under such conditions.

Klüber Klüberfluid B-F 1 Ultra

Running-in lubricant for open drives

Application Klüber Klüberfluid B-F 1 Ultra

Klüberfluid B-F 1 Ultra is used in the splash, paddle wheel or circulation lubrication of open gears for running-in lubrication or tooth profile correction. Possible uses are limited neither by component size nor by driving power. The peripheral speed should not exceed 8.5 m/s. Drives of this kind are mainly used in rotary kilns, tube mills, and similar machines as are used in the cement, lime, gypsum, mining and chemical industries. Klüberfluid B-F 1 Ultra is not suitable for the lubrication of (rolling or sliding) bearings.

Klüber Klüberfluid C-F 4 Ultra

Transparent operational lubricant for large open gear drives

Application Klüber Klüberfluid C-F 4 Ultra

Klüberfluid C-F 4 Ultra can be applied by immersion, transfer paddle wheel, pressure fed circulation and spray lubrication systems. It can be used with all gear sizes and power ratings. A peripheral speed of 7 m/s should however not be exceeded. Open gear drives are found in rotary kilns, tube mills, drums and similar machinery used in the cement, lime, gypsum, mining and chemical industries as well as in power stations. It can also be used for medium-size to large girth gear drives in sugar and paper production as well as in the marine and offshore sector.

Klübersynth G 4-130

Synthetic high-performance gear oil

Application Klübersynth G 4-130

Klübersynth G 4 was especially developed for the lubrication of spur, bevel and planetary gears. It can also be used for plain and rolling bearings.

Klüber Grafloscon D-SG 00 Ultra

Repair lubricant for open drives

Application Klüber Grafloscon D-SG 00 Ultra

GRAFLOSCON D-SG 00 ULTRA was developed for repair lubrication of damaged tooth flanks of open gears. It is also suitable for forced running-in of new or readjusted girth gear/ pinion drives on rotary kilns, tube mills, rotary drums, etc. used mainly in the cement, mining and chemical industries.

Klüber Klüberfluid C-F 3 M Ultra

Operational lubricant for large girth gear drives

Application Klüber Klüberfluid C-F 3 M Ultra

Klüberfluid C-F 3 M ULTRA is primarily used for the lubrication of rather large gear-rim/pinion drives. It can be used with all gear sizes and power ratings. A peripheral speed of 12 m/s should however not be exceeded. Klüberfluid C-F 3 M ULTRA was especially developed for ships and the offshore sector, where most of such drives are found. However, application is also in other industries.

Klübersynth GEM 4-320 N

Synthetic high-performance gear and multipurpose oil with KlüberComp Lube Technology

Application Klübersynth GEM 4-320 N

Klübersynth GEM 4 N was specially developed for the lubrication of spur, bevel, hypoid and planetary gears that are subject to high loads. Such gears are frequently used in the wind, steel, mining and sugar industries. It is also used for the lubrication of standard worm gears as defined in DIN 3996. Klübersynth GEM 4 N can also be used for the lubrication of plain and rolling bearings, all kinds of toothed couplings, chains, guideways, joints, spindles and pumps, especially in applications where the equipment is exposed to elevated temperatures or pronounced temperature fluctuations.